Omnimount OMF Mounting System for 13 to 42-Inch Flat Panel Televisions

5 Responses to “ Omnimount OMF Mounting System for 13 to 42-Inch Flat Panel Televisions ”

1. Alfred M. Neill
   December 27, 2009 at 10:21 pm

   I loved the easy setup of this mount.

   That said, the TV and situation I originally wanted to use this to mount was unsuited to this product.

   Because the back is nearly flush with the wall, you must ensure your power cable goes through the wall and is pre positioned along with the other cables. And more importantly, it is not a good choice of mounts if you will need to be swapping cables/components in and out of the back panel a lot. This is why we abandoned our original intended use for this mount.

   However, our second plan for the mount works fine, setting up TV mounted higher on a wall, with all the components down low, using 12′ HDMI cables to connect the components to the TV through the wall. Of course the fact that it doesn’t angle down makes it a bit of a pain for high wall use, but the room is large enough where the viewing angle is manageable. And this way the kids can change the DVDs and we don’t have fingerprints on the screen.

   I wish EVERY mount was this easy to set up, and the price is MORE than right!
   Rating: 4 / 5
2. JAG
   December 27, 2009 at 11:51 pm

   Setup is extremely easy. Dimension layouts are easy for me but I’m sure that some underachievers would have difficulty. As with all mounting brackets, you need to calculate distances from floor to bottom of TV, up to mounting device, up to the top of the TV, then up to the ceiling (If you want a centered picture). Once the calculations are compiled, setup is a piece of cake. Just screw the attachments to the wall and to the back of the TV and your ready to go. I also recommend that even if the tv only weighs 20 lbs, you should still go into the stud for added security. If anyone leans on it by accident, it will probably come off the wall because of the excess weight.
   Rating: 5 / 5
3. Bradley Olin
   December 28, 2009 at 12:32 am

   The Omnimount was extremely easy to install. My wife, who is not tech savvy at all, or remotely handy, was able to successfully use the supplies to line up our mount and put our 36″ flat screen tv on the wall of our new home. It looks great and was painless! It was a little pricier than other mounts, but the simplicity makes up for it! One small problem, as with most wall mounts, is what to do with all the cords running from your tv to other devices and power outlets. It’d be nice if someone invented a mounting device that took care of that unsightly issue.
   Rating: 4 / 5
4. Nathan Beauchamp
   December 28, 2009 at 3:10 am

   I’ve been installing commercial grade white boards and display boards for over 7 years. I’ve always used HILTI wall mounts for that purpose (their rated at 75 pounds per mount!) and so I immediately recognized that these Omnimount mounts use the exact same concept as the HILTI mounts. I’m impressed with how much weight they will sustain, although now that we’re in the era of 30-40lbs flat screens these are actually provably overkill for most applications. These Omnimounts will absolutely support any flat panel you through at them (at least up to 42″) easily enough.

   Installation is very easy. The mounting system comes with a cardboard pattern to help place the mounts brackets in the correct place. All you really need is a power drill and a screwdriver. You can have this wall mounting system up in less than 30 minutes if you know what you’re doing. Once in place, it provides a very flush mount with little to no wasted space behind the TV panel. Depending on the inputs of your particular brand of tv, this could present a problem for cabling. If your HDMI inputs point straight out the back of the panel, you’ll need to make a pretty sharp right angle turn with the HDMI cable, which means you’ll want a fairly flexible HDMI cable.

   The only downside to this system is that of viewing angle once the TV is installed. If you’re installing it directly across from your seating arrangement and at mid-eye level, viewing angle wont be in issue. However, if you’re mounting the TV up higher (for example above a fireplace mantle) these Omnimounts don’t give you the flexibility of a more expensive mounting bracket that allows you to tilt the screen downwards. This isn’t a failing of the Omnitmounts, but is a limitation worth mentioning. If you plan to mount at eye level (which is actually recommended for best performance from flat panels whether they’re LCD or PLASMA), this won’t be an issue.

   Overall this is a really great kit for the cost, especially if you plan to mount at eye level. At about a fourth of the cost of a full mounting kit, Omnimounts are a good alternative to higher priced options.

   4.5/5 Stars
   Rating: 4 / 5
5. Ray Stoecklin
   December 28, 2009 at 3:43 am

   I acquired this mount to pin my computer monitor to an exact location on the wall. Unlike most other mounts, this one advertises to work with drywalls, therefore not needing to use a stud finder or imposing limits on location. I expected some extra engineering feat because of this (perhaps some sort of wall plate with multiple drill holes to spread the load), but this turned out to not be the case. The load will be secured only in four places. I don’t think I’d attempt to hang my 42″ Plasma on a drywall, but if you have a lighter TV (LCD) this may work for you. It did work very well for my 21″ computer LCD.

   The packaging is very compact and neat (reminds you of a certain Cupertino- based company); and instructions are simple (although in my package, the booklet refers to items as 1,2,3.. whereas in the plastic bags they are labeled as A,B,C… minor detail). If you are installing on a drywall, all you need is a power drill, everything else (including the drill bit) is included. If you’re installing onto masonry or wood (studs) you need additional tools. Because there are four stubs to be individually fixed to the wall, you need to be careful to level and space them out correctly. To help you with this, there is a cardboard template that also includes a simple bubble level. My template was a little warped and the bubble level fell off at some point, so I wish this was made of plastic, not paper (and to equalize the environmental footprint, the packaging could be made of paper, not plastic!).

   Overall, as a trouble- free, thought-out solution for what I happened to have in mind, this was a winner. I’m only subtracting 1 star because of the cardboard template and my nagging thought that additional mount points would be necessary for carrying a heavier-than-average 42″ TV.
   
   Rating: 4 / 5